|
John,
the software translation in french is so bad that
one migth be better without it.
Le premier objectif est de faire des tirages de grande qualité et ce
peut importe la façon d'appliquer l'émulsion.
Regards,
Yves
----- Original Message -----
Sent: Thursday, January 17, 2008 4:27
PM
Subject: Re: Coating Without a
Machine
Art,
I think that
your following statement is so important and helpful that I
am including translations to our European friends.
Thank you.
John - Photographist - London -
UK.
Cher John,
le premier
objectif doit faire des copies de qualité avec celui qui le processus
enduisant soit nécessaire.
Sincèrement, Art.
..........................................................................................
Estimado Juan,
el objetivo
primario debe hacer impresiones de la alta calidad con lo que el proceso de
capa es necesario.
Sinceramente, Art.
----- Original Message -----
Sent: Thursday, January 17, 2008 8:25
PM
Subject: Re: Coating Without a
Machine
Dear John,
The primary objective is to make high quality prints
with whatever coating process is neccessary.
Sincerely, Art
---------- Original Message -----------
From: John
Grocott <john.grocott403@ntlworld.com>
To: The List <alt-photo-process-l@usask.ca>
Sent: Thu, 17 Jan 2008 14:10:38 +0000
Subject: Coating Without a
Machine
> Hi Philippe, Art,
Sandy, Dick and All,
>
I
have found possible, tho' amittedly tricky, a successful Direct
Carbon coating procedure, by hand, with only a Hake brush or
similar , probably in the same way that Artigue and
Great grandfather Fresson and many others have found it possible.
>
> Whether you could
make the result ''commercial'' or not depends on what price tag you would
put on it. Dont forget, this is approaching the ''funny money''
level.
>
> At any event
as many Gum worker take for granted they do not use a machine for coating,
unless a brush might be described as a machine.
>
> Much depends on the type of
coatings you have arrived at. Gelatine takes much practice to control with a
brush
> and, probably, more
so if a machine is used.
>
> With the complex equipment decribed below I would
advise that, certainly, ''rethinking alternatives'', is definately, in
order.
>
............................................................
>
> Computer French
for Phillipe and others:-
> .....................................................................
> J'ai eu la possibilité de
réaliser ce procédé enduisant de carbone direct évidemment rusé, à la main,
avec seulement une brosse de merluches ou semblable, probablement de la même
manière qu'Artigue et grand Fresson première génération et beaucoup d'autres
l'ont trouvée possible.
> Si vous pourriez faire le ''
commercial de '' de résultat ou pas dépend de quelle étiquette des prix vous
la mettriez dessus. N'oubliez pas, ceci approche le niveau de '' de fausse
monnaie de ''.
> À aucun événement autant de prise d'ouvrier de gomme
pour accordée eux n'utilisent une machine pour enduire, à moins qu'une
brosse pourrait être décrite comme machine.
> Beaucoup dépend du type
d'enduits que vous êtes arrivés à. La gélatine prend beaucoup de pratique de
commander avec une brosse
> et, probablement, plus ainsi si une
machine est utilisée.
> Avec l'équipement complexe décrit ci-dessous
je conseillerais ce, certainement, le '' repensant le '' de solutions de
rechange, est certainement en règle.
>
> Good Luck
>
> John- Photographist
- London - UK.
>
>
>
>
----- Original Message -----
> From: achakali@wideopenwest.com
> To: alt-photo-process-l@usask.ca
> Sent: Thursday, January 17, 2008 6:22 AM
>
Subject: Re: Réf. : Re: Fresson = Echague Look.
>
>
> Phillippe,
>
> I am not aware of a
technique to make direct print paper by hand, that is to say, without
equipment. I only
wish it were possible.
>
> Actually Sandy's comment about how it should
be possible has started me to rethink alternatives.
However, all three of the coatings needed are currently
sprayed. I have shared photos of my spray coating
system during each of my APIS presentations. The
equipment includes a spray booth, a heated chamber, and a force air
dryer. At that, it is
not all of what is needed for a commercial product.
>
> Sincerely, Art
>
>
>
>
>
------- End of Original Message -------
|